Baja Table / Sun Shelf Umbrella Table 
If you have been looking for a table to use on your Sun Shelf / Baja Ledge, and you have an umbrella pocket in your pool, you have just found it!
The SunShelf is a great umbrella table that you can slide right into your existing umbrella pocket in your pool. All you have to do is remove the cap on the umbrella pocket and slide the SunShelf table in the hole.
We offer two sizes to suit your needs.
- Our Patent Pending Universal Anchor will fit almost every sleeve style. The wedge anchor design will allow you to place the anchor in your sleeve hole, turn the jam nut knob, and it locks right into your standard 7″ deep umbrella sleeve. If you have a bronze SR SMITH, 5″ Deep AquaStar, or a ColorMatch (The one you fill the cap with the same color pool finish) you will just need an adapter, and you are good to go!
- We have a 22″ high Sun Shelf Table Rod, which will work perfectly for your shallow water ledge where you may want to place your normal plastic chairs on the shelf. Many people use lounge chairs on the ledge, and this table will give you the perfect height to keep your drinks secure and close by. This option will hold an umbrella with a pole of up to 1.6″ The table height would be about 22″ above the bottom of the pool.
- The 40″ SunShelf will give you about a 40″ bistro/pub-style umbrella table. This is great for the people who like to stand up when using the Sun Shelf Table.
The 18″ table top is our new super heavy-duty table top, which will hold most of the popular stainless steel tumblers and large foam can coolers.
You can also add our LED light kit to the table.
Umbrellas are not included, but we have some available here. We recommend only using an umbrella with anodized aluminum or fiberglass pole. This will keep rust out of your pool.
Proudly Made in the USA.
Patents Pending
You can also add umbrella pockets to existing pool decks. You may need a contractor to install a pocket for you, but we can recommend an umbrella sleeve that will work great for you.
PLEASE READ THE Q&A SECTION BELOW BEFORE ORDERING to make sure you do not need an adapter. If you have any questions please send us a message and photo of your umbrella sleeve.
Questions (Q) and Answers (A)
Q) Will this work in saltwater pools?
A) Yes! Our product will work in saltwater and chlorine pools. Our materials will not rust in your pool.
Q) How tall is the table support rod?
A) We have Support Rods in 22 and 40 inches available.
Q) What size umbrella will work with the table?
A) Any umbrella with a 1.6″ lower pole will work, however, we recommend an umbrella with an anodized aluminum or fiberglass pole.
Q) Is the table stable?
A) The table is super heavy-duty. The support rod is designed to move a little when someone runs into it. It will essentially wiggle, but will not flop around.
Q) What size umbrella sleeve/ pocket will the table rod fit in?
A) Aqua Star 7″ deep sleeves. CMP Waterways, or ColorMatch (with adapter). Please check and verify your umbrella sleeve and order the appropriate adapter if needed for color match, 5″ deep sleeves, or SR Smith. The photos show what one of the above sleeves looks like on the inside. If yours looks like this, select that you have a 2″ step on the inside of your sleeve.
The Universal BajaTable will fit. It looks like a homemade umbrella sleeve where standard 1-1/2″ schedule 40 PVC was used to make an umbrella sleeve. You will see where the upper portion of the cap is glued onto the PVC pipe. It may look like there is a step, but
SR Smith as shown below is a bronze sleeve for gunite, shotcrete, or concrete pools. You just need to order an adapter, and it fits great.
Aquastar, Waterways, CMP Sleeves Look Similar
Straight Sleeve
Made from PVC pipe by your pool builder. Look for a glue line or evidence of a gap where the cap meets
the pipe.. It does not taper, and it goes straight down the side walls.
1.90 SR SMITH SLEEVES
Q) I have an SR Smith Bronze 1.90″ sleeve in my pool. Will this work? 
A) It will! You just need to order the SR Smith adapter
Q) I have an SR Smith 1.90 sleeve that goes in a vinyl liner pool. What table rod should I order?
A) You will want to order the SR Smith adapter.
Q) Will this work with a Color Match Pool Sleeve / Pole Holder?
A) If you have the Color Match, Pebble Top pool sleeve, our table rod will fit with the Color Match adapter. This is the style that has a little cap that is filled with pebbles to match your pool finish.
Q) My sleeve in my pool has threads at the top of it about an inch or so down. Will this work?
A) If your sleeve has multiple threads at the top where it has a plug that screws into it, it is a homemade fitting, and it will work without any adapters.
